From 8376ef56580626e9c0f796d5b85b53a0a1c7d5f5 Mon Sep 17 00:00:00 2001
From: V3n3RiX <venerix@redcorelinux.org>
Date: Sat, 14 Jul 2018 21:03:06 +0100
Subject: gentoo resync : 14.07.2018

---
 app-laptop/tp_smapi/files/tp_smapi-0.40-confd | 20 ++++++
 app-laptop/tp_smapi/files/tp_smapi-0.40-initd | 92 +++++++++++++++++++++++++++
 2 files changed, 112 insertions(+)
 create mode 100644 app-laptop/tp_smapi/files/tp_smapi-0.40-confd
 create mode 100644 app-laptop/tp_smapi/files/tp_smapi-0.40-initd

(limited to 'app-laptop/tp_smapi/files')

diff --git a/app-laptop/tp_smapi/files/tp_smapi-0.40-confd b/app-laptop/tp_smapi/files/tp_smapi-0.40-confd
new file mode 100644
index 000000000000..7c80f35e390b
--- /dev/null
+++ b/app-laptop/tp_smapi/files/tp_smapi-0.40-confd
@@ -0,0 +1,20 @@
+# /etc/conf.d/smapi: config file for /etc/init.d/smapi
+
+# use '/etc/init.d/smapi info' at any time to check the thresholds
+# currently used by the driver
+# Note that the kernel does some sanity checking on the values and
+# will not accept any combination of values you may try to set up.
+# (i.e. stop value lower than start) So if the output of info does
+# not match what you wanted the driver probably did not like your
+# configuration.
+
+# default thresholds for '/etc/init.d/smapi start'
+SMAPI_THRESH_START="30"
+SMAPI_THRESH_STOP="85"
+# values to be used for '/etc/init.d/smapi low'
+SMAPI_LOW_THRESH_START="${SMAPI_THRESH_START}"
+SMAPI_LOW_THRESH_STOP="${SMAPI_THRESH_STOP}"
+
+# values to be used for '/etc/init.d/smapi high'
+SMAPI_HIGH_THRESH_START="95"
+SMAPI_HIGH_THRESH_STOP="100"
diff --git a/app-laptop/tp_smapi/files/tp_smapi-0.40-initd b/app-laptop/tp_smapi/files/tp_smapi-0.40-initd
new file mode 100644
index 000000000000..3b8c10d9274a
--- /dev/null
+++ b/app-laptop/tp_smapi/files/tp_smapi-0.40-initd
@@ -0,0 +1,92 @@
+#!/sbin/openrc-run
+# Copyright (C) 2011 Henning Schild <henning@wh9.tu-dresden.de>
+# Copyright (C) 2011 Sebastian Pipping <sebastian@pipping.org>
+#
+# Distributed under the terms of the GNU General Public License, v2 or later
+
+extra_started_commands="low high info"
+
+SMAPI_SYSFS="/sys/devices/platform/smapi"
+BATS="BAT0 BAT1"
+
+depend() {
+	after modules
+}
+
+start() {
+	local state1
+	local state2
+
+	ebegin "Making sure that module 'tp_smapi' is loaded"
+	modprobe tp_smapi
+	state1=$?
+	eend ${state1}
+
+	ebegin "Checking for \"${SMAPI_SYSFS}\""
+	test -d "${SMAPI_SYSFS}"
+	state2=$?
+	eend ${state2}
+
+	if [ "${state1}" -ne "0" ] || [ "${state2}" -ne "0" ]; then
+		return 1
+	fi
+
+	ebegin "Starting ${SVCNAME}"
+	set_all ${SMAPI_THRESH_START} ${SMAPI_THRESH_STOP}
+	eend $?
+}
+
+stop() {
+	einfo "Nothing required to be done to stop ${SVCNAME}"
+}
+
+require_started() {
+	if ! service_started; then
+		"${RC_SERVICE}" start || return $?
+	fi
+}
+
+high() {
+	require_started
+
+	einfo "Switching ${SVCNAME} to high thesholds"
+	set_all ${SMAPI_HIGH_THRESH_START} ${SMAPI_HIGH_THRESH_STOP}
+}
+
+low() {
+	require_started
+
+	einfo "Switching ${SVCNAME} to low thesholds"
+	set_all ${SMAPI_LOW_THRESH_START} ${SMAPI_LOW_THRESH_STOP}
+}
+
+set_all() {
+	local tstart=$1
+	local tstop=$2
+	local bat
+
+	for bat in ${BATS}; do
+		ebegin "  setting thresholds for ${bat}: $tstart $tstop"
+		echo ${tstart} > ${SMAPI_SYSFS}/${bat}/start_charge_thresh
+		echo ${tstop} > ${SMAPI_SYSFS}/${bat}/stop_charge_thresh
+		eend $?
+	done
+}
+
+info() {
+	local presence
+	local tstart
+	local tstop
+	local bat
+
+	require_started
+
+	for bat in ${BATS}; do
+		tstart=$(cat ${SMAPI_SYSFS}/${bat}/start_charge_thresh)
+		tstop=$(cat ${SMAPI_SYSFS}/${bat}/stop_charge_thresh)
+		if [ "$(cat ${SMAPI_SYSFS}/${bat}/installed)" -eq "1" ]; then
+			presence="  [installed]"
+		fi
+		einfo "${bat}: ${tstart} ${tstop}${presence}"
+	done
+}
-- 
cgit v1.2.3