gentoo christmass resync : 25.12.2020

2 files changed, 0 insertions, 82 deletions

diff --git a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-cmdline.txt b/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-cmdline.txt
deleted file mode 100644
index 39112a2dba61..000000000000
--- a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-cmdline.txt
+++ /dev/null
@@ -1 +0,0 @@
-ipv6.disable=0 selinux=0 plymouth.enable=0 smsc95xx.turbo_mode=N dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=noop rootwait
diff --git a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-config.txt b/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-config.txt
deleted file mode 100644
index 9401530925de..000000000000
--- a/sys-boot/raspberrypi-firmware/files/raspberrypi-firmware-0_p20130711-config.txt
+++ /dev/null
@@ -1,81 +0,0 @@
-#from archlinux arm sdcard image
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-#disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-#hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# for more options see http://elinux.org/RPi_config.txt
-
-## Some over clocking settings, govenor already set to ondemand
-
-##None
-#arm_freq=700
-#core_freq=250
-#sdram_freq=400
-#over_voltage=0
-
-##Modest
-#arm_freq=800
-#core_freq=300
-#sdram_freq=400
-#over_voltage=0
-
-##Medium
-#arm_freq=900
-#core_freq=333
-#sdram_freq=450
-#over_voltage=2
-
-##High
-#arm_freq=950
-#core_freq=450
-#sdram_freq=450
-#over_voltage=6
-
-##Turbo
-#arm_freq=1000
-#core_freq=500
-#sdram_freq=500
-#over_voltage=6
-
-gpu_mem_512=316
-gpu_mem_256=128
-cma_lwm=16
-cma_hwm=32
-cma_offline_start=16
-